Jeti ECO Brushless Motor Controllers from Hobby Lobby!

Jeti ECO - low cost brushless motor controllers are the easiest to use

Jeti's ECO line of brushless controllers with BEC (battery eliminator circuit) offers the sport modeler a low cost choice in high quality controllers. Controllers "auto-detect" the number of poles in the motor and pick the optimal timing. The settings have been reduced to four modes simply selected by jumper, no programming required. Controllers "auto-detect" full throttle position. Each unit can run up to 4 servos when used with up to 3 lithium cells. Controllers have temperature overload protection and will cut the power to the motor if controller reaches 100-110 degrees C. All Jeti controllers come with a 2-year free replacement warranty!

Mode 1: NiCad/NiMH – Brake Off
Non-active brake with slow down type low voltage cut-off down to 5 volts or 0.7 volts per cell.

Mode 2: NiCad/NiMH – Brake On
Active brake with hard type low voltage cut-off at 5 volts or 0.7 volts per cell.

Mode 3: LiIon/LiPoly – Brake Off
Non-active brake with slow down type low voltage cut-off. Minimum voltage 6 volts for 2 cell packs, 9 volts for 3 cell packs.

Mode 4: LiIon/LiPoly – Brake On
Active brake with hard type low voltage cut-off. Minimum voltage 6 volts for 2 cell packs, 9 volts for 3 cell packs.

For 2 to 3 Li-Po cells, to 8 amps

1" x 5/8" x 3/16", 7 grams (1/4 oz.), 8 Amps continuous, for 2 to 3 Lithium cells. BEC can run a maximum of 4 servos. The brake can be turned on and off using your transmitter. The low voltage cutoff is set for 3V per cell.

Jeti ECO 8 Amp Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 12 amps

1-3/4" x 1" x 1/4", 10 grams (1/3 oz.) 12 amps continuous, for use with 6-10 NiCad or NiMH, 2-3 Lithium cells. BEC can run 4 servos with up to 3 Lithium cells, or 3 servos if 10 NiCad/NiMH are used.

Jeti ECO 12 Amp Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 18 amps

1-3/4" x 1" x 5/16", 21 grams (3/4 oz.) 18 amps continuous, for use with 6-10 NiCad or NiMH, 2-3 Lithium cells. BEC can run 4 servos with up to 3 Lithium cells, or 3 servos if 10 NiCad/NiMH are used.

Jeti ECO 18 Amp Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 25 amps

1-3/4" x 1" x 7/16", 28 grams (1 oz.) 25 amps continuous, for use with 6-10 NiCad or NiMH, 2-3 Lithium cells. BEC can run 5 servos on 4-6 NiCad/NiMH cells or 2 Lithium, 4 servos with 7-8 NiCad/NiMH cells or 3 Lithium, or 3 servos if 10 NiCad/NiMH are used.

Jeti ECO 25 Amp Brushless Motor Controller

Jeti ECO Brushless Controllers