Jeti Advance PLUS Programmable Brushless Motor Controllers from Hobby Lobby!

Jeti "Advance PLUS" - the only name you need to know
for brushless motor controllers

Jeti Advance PLUS Programmable Brushless motor Speed Controls

We think: that Jeti Advance PLUS is the world's best controller for brushless motors.

We know: that Jeti Advance PLUS is the world's EASIEST to program

Jeti Brushless Motor Controllers Which do you think is easier to program?

Our competition's programming instructions to set the Motor Cutoff Voltage:
"1 flash - short pause -- 4 flashes - long pause (means) Setting 1 (cutoff voltage), Option 4 (712V, Your response: Yes - Throttle stick in up position, No - Throttle stick in off position, (controller) stores the selection. Flashes rapidly to confirm receipt of your response. (Your action): Return TX stick to center and proceed to next setting -- Current Limiting (9.2v below)....(continued...)

Jeti Advance PLUS's programming instructions to set the Motor Cutoff Voltage:
"Plug jumper in HIGH position." (That's it!)

Basic programming of Advance PLUS -- choosing Brake ON or OFF and Hard or Soft timing -- can be done without the Programming Card. Detailed programming of the Jeti Advance PLUS is done by using this tiny 1-1/2" x 1-1/2" Programming Card that is only 1/16" thick. Carry it in your pocket or your field box -- it has ALL the advanced programming functions in it. Just move the jumper connectors to the value you select. With the Programming card you can program or select the following:
Jeti Advance PLUS program card
1. NiCad and NiMH or Lithium battery,
2. Motor Cutoff Voltage,
3. Hard or Soft Cutoff,
4. Prop Brake On or Off,
5. Timing: Low for normal motors, High for Outrunners,
6. Throttle Response: Linear or Logarithmic.

These super reliable controllers have:
Very smooth throttle response;
Superb operation with OUTRUNNER motors;
Automatic motor cutoff with automatic detection of the number and the type of battery cells;
Safety cutoff when using Lithium batteries that prevents accidental destruction of the Lithium battery due to over discharge;
High frequency brake with non linear hard or limited braking action;
Automatic self-calibrating when you turn on your transmitter;
Automatic motor cutoff when battery voltage is low;
8 kHz switching rate.
These can be easily programmed to operate either normal brushless motors or to operate OUTRUNNER motors.

See table below for number of servos that can be used with each Advance PLUS controller.

Jeti Warranty & Repair Policy

The Programming Card for all the Advance PLUS controllers

1-1/2 x 1-1/2 x 1/16" card with jumper connectors programs all of the Advance PLUS controllers in 6 different ways:

Accept Nicads or NiMh or Lithium cells;
Set a High or Low motor cutoff voltage;
Set a Hard cutoff or a gradual slowdown;
Set Brake or No Brake;
Set Timing for Regular Brushless motors or for Outrunner motors;
Set Throttle response either Linear or Logarithmic.

If you do NOT use the Program Card, then the Advance PLUS Controllers can only be programmed as the Jeti Advance Controllers were: Brake On or Off, Hard (Outrunner) or Soft timing.

Program Card
Jeti Advance PLUS program card

Jeti Advance PLUS Brushless Controllers

For 6 to 8 Ni, 2 to 3 Li-Po cells, to 4 amps

1 x 5/8 x 3/16", 6 grams (1/5 oz.), 4 Amps continuous, for 6 to 8 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 3 servos if 7 or 8 cells. Order connector set MJ21011.

4 amp

NEW! Lighter version of 8 amp controller

1 x 5/8 x 3/16", 7 grams (1/4 oz.), 8 Amps continuous, for 6 to 8 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 3 servos on 7 or 8 cells. Order connector set MJ21011.

Mini 8 amp
Jeti Mini 8 Amp Advance PLUS Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 8 amps

1-1/4 x 7/8 x 1/4", 9 grams (1/3 oz.), 8 Amps continuous, for 6 to 10 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos if 10 cells. Order connector set MJ21011.

8 amp

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 12 amps

1-1/4 x 7/8 x 1/4", 10 grams (1/3 oz.), 12 Amps continuous, for 6 to10 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos if 10 cells. Order connector set MJ21021.

12 amp
Jeti 12 Amp Advance PLUS Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 18 amps

1-1/4 x 7/8 x 5/16", 21 grams (3/4 oz.), 18 Amps continuous, for 6 to 10 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos if 10 cells. Order connector set MJ21021.

18 amp
Jeti 18 Amp Advance PLUS Brushless Motor Controller

For 6 to 10 Ni, 2 to 3 Li-Po cells, to 30 amps

1-5/8 x 7/8 x 5/16", 28 grams (1.0 oz.), 30 Amps continuous, for 6 to 10 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 3 servos if 10 cells. Connectors included.

30 amp
Jeti 30 Amp Advance PLUS Brushless Motor Controller

For 6 to 12 Ni, 2 to 3 Li-Po cells, to 40 amps

2 x 1 x 3/8", 35 grams (1-1/4 oz.), 40 Amps continuous, for 6 to 12 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 5 servos on 6 cell battery, 3 servos if 12 cells. Connectors included.

40 amp
Jeti 40 Amp Advance PLUS Brushless Motor Controller

For 6 to 16 Ni, 2 to 6 Li-Po cells, to 40 amps

2 x 1 x 5/16", 35 grams (1-1/4 oz.), 40 Amps continuous, for 6 to 16 nicads or NiMh, 2 to 6 Lithium cells. There is no BEC on this controller. Connectors included.

40 amp Opto
Jeti 40 Amp Advance PLUS Opto Brushless Motor Controller

For 8 to 24 Ni, 3 to 8 Li-Po cells, to 45 amps

2 x 1 x 3/8", 38 grams (1-1/3 oz.), 45 Amps continuous, for 8 to 24 nicads or NiMh, 3-8 Lithium cells. There is no BEC on this controller. Connectors included.

45 amp Opto
Jeti 45 Amp Advance PLUS Opto Brushless Motor Controller

For 6 to 12 Ni, 2 to 3 Li-Po cells, to 70 amps

2 x 1 x 1/2", 38 grams (1-1/3 oz.), 70 Amps continuous, for 6 to 12 nicads or NiMh, 2 to 3 Lithium cells. BEC can run 5 servos on 6 cell battery, 3 servos if 12 cells. Connectors included.

70 amp
Jeti 70 Amp Advance PLUS Brushless Motor Controller

For 6 to 16 Ni, 2 to 6 Li-Po cells, to 70 amps

2 x 1 x 3/8", 38 grams (1-1/3 oz.), 70 Amps continuous, for 6 to 16 nicads or NiMh, 2 to 6 Lithium cells. There is no BEC on this controller. Connectors included.

70 amp Opto
Jeti 70 Amp Advance PLUS Opto Brushless Motor Controller

For 8 to 30 Ni, 3 to 10 Li-Po cells, to 77 amps

2 x 1 x 1/2", 40 grams (1-3/8 oz.), 77 Amps continuous, for 8 to 30 nicads or NiMh, 3 to 10 Lithium cells. There is no BEC on this controller. Connectors included.

77 amp Opto
Jeti 77 Amp Advance PLUS Opto Brushless Motor Controller

For 14 to 32 Ni, 5 to 10 Li-Po cells, to 90 amps

2-1/2" x 2-1/8" x 5/8", 3.8 oz. Use with large AXI outrunner motors in demanding applications. Large 2" x 2" x 5/16" aluminum heat sink dissipates excess heat. Solid screw-in-place installation with 3 rubber grommet shock mounts. 2.5mm silicone insulated wire on motor leads, 3mm silicone insulated wire on battery leads. 11" long wire to receiver.

90 amp Opto
Jeti 90 Amp Advance PLUS Opto Brushless Motor Controller

18 amp controller for helicopter and Variable Pitch Prop

1-1/2" x 7/8" x 1/4", 23 grams (7/8 oz.) Brushless Helicopter and Variable Pitch Prop controller with BEC. Use with JESAP03 Program card. Similar to the other Advance PLUS controllers with choices of battery type, battery cut off voltage and timing for either Inrunner or Outrunner brushless motors. The helicopter settings are: Heli mode Normal -- this has the throttle stick control the RPM. Heli mode Constant Speed, also called governor mode, where the controller maintains a constant RPM regardless of change in Pitch of blades. The 3D Setting makes the controller react quickly to hold a constant RPM when used with the Constant Speed setting. The Normal position provides slower (soft reactions) to RPM change. For 6-10 Ni, 2-3 Li cells, to 18 Amps.

18 amp Heli
Jeti 18 Amp Advance PLUS Helicopter Controller

For 3 to 4 NiCad or 1 LiPoly cell, to 4 amps

1 x 5/8 x 5/32", 6 grams (1/5 oz.), 4 amps continuous. Non-programmable controller for OUTRUNNER brushless motors that are powered by a single LiPoly cell (FM151) or 3-4 cell NiCad or NiMH battery packs. Order connector set MJ21011.

4 amp

Number of Servos used on Advance Controllers that have BEC

Controller	Cells/Servos NiCd or NiMH	Cells/Servos Li-Polymer
04	6/4, 8/3	2/4, 3/3
08	6/4, 8/3, 10/2	2/4, 3/3
12	6/4, 8/4, 10/2	2/4, 3/3
18	6/4, 8/4, 10/2	2/4, 3/3
30	6/4, 8/4, 10/3	2/4, 3/3
40	6/5, 8/5, 10/4, 12/3	2/5, 3/4
70	6/5, 8/5, 10/4, 12/3	2/5, 3/4

Note* - When using economy class micro servos, reduce the number of servos by one. When using fast or digital servos, reduce the number of servos by two.

Advance PLUS Controllers: 4 Amp \| 8 Amp \| 12 Amp \| 18 Amp \| 30 Amp \| 40 Amp \| 70 Amp
Advance PLUS OPTO Controllers: 40 Amp \| 45 Amp \| 70 Amp \| 77 Amp \| 90 Amp
Helicopter Controller: 18 Amp \| Single LiPoly Controller: 4 Amp

Jeti Advance PLUS Brushless Motor Controllers

Jeti Advance PLUS
Brushless Motor Controllers