Gearboxes for SPEED 280, SPEED 300 motors from Hobby Lobby!

Gearboxes with ballbearings, for SPEED 280 motors:

MJ Gearboxes for SPEED 280 motors

Very high quality gearboxes with a super ballbearing. If you have had trouble with other 280 gearboxes, these may solve your problems. The prop shaft is 3mm diameter. See adapters for these gearboxes.

High Ratio Gearbox for SPEED 300

High ratio gearbox for
3 and 4 bladed props

Very high ratio gearbox allows the use of large props with Speed 300 motor. Ideal for the 3 and 4 bladed props from Flying Styro (FS300, FS400). Gearbox mounts through the firewall and is glued in place. Comes with 3mm prop shaft adapter, aluminum sleeve adapter for Flying Styro props, and glue for attaching the pinion to your motor.

Gearboxes with ballbearings, for SPEED 300 motors:

MJ Gearboxes for SPEED 300 motors

Very high quality gearboxes with a super ball bearing. The prop shaft is 3mm diameter. See adapters for these gearboxes.

Prop adapters and prop nut for MJ Gearboxes:

Short prop adapter

Long prop adapter

Round Head Nut

The prop adapters are collet type for perfect centering on 3mm shaft. They include a prop nut but the fancy rounded prop nut is offered for scale and safety reasons.

"Front Adapters" allow you to mount MJ gearboxes
for SPEED 280 or SPEED 400 directly to the nose of an airplane

Gearbox adapter

These screw to the front of MJ gearboxes to allow you to attach the gearbox directly to the nose of the airplane instead of having to mount the gearbox to the aft-located firewall.

The screw spacing for the Front Adapters is the same as the spacing of screws on the 280 or 400 motors.

A way to mount MJ Gearboxes to a flat plate

Gearbox mount

Plastic "strap" sets that are slightly larger diameter at the gearbox end and slightly smaller at the motor-only end so that they accurately mount MJ Gearbox with motor in place to a flat, cutout wood plate.

4:1, 5:1, 6:1 JH Gearboxes for SPEED 280 Motors

The output shafts are 6mm diameter plastic (exceptions are noted). FS200 and FS300 propellers are press fits onto this shaft. Slowflyer Props P07040SF through P11070SF also will fit onto these JH gearboxes. Drill the prop hubs to 6mm diameter to fit. Props and also the small pinion gears can be secured with CA if they slip. (See the Props for JH gearboxes at the bottom of this page)

4:1 Ratio for SPEED 280

For 280 motor and Flying Styro 2 and 3 blade propellers. 1.30" high. Two front mounting holes are 1.3" apart. Bronze bushing!

Props for JH Gearboxes
Prop blades and Midparts	FS001 9x7 Single Prop Blade ..... $ 1.00 ESTIMATED ARRIVAL 02/16/09 - Please Preorder Now FS101 Midpart 2 Blade Holder, 6mm ..... $ 1.00 AVAILABLE NOW FS103 Midpart 3 Blade Holder, 6mm ..... $ 1.00 AVAILABLE NOW

Complete Props
Complete Props	FS200 2 Blade 9x7 Prop Complete ..... $ 3.00 AVAILABLE NOW FS300 3 Blade 9x7 Prop Complete ..... $ 4.00 AVAILABLE NOW

3 Blade Prop for GWS Geardrive
Prop for GWS gearboxes	FS305 3 Bladed 9x7 Prop for GWS Drive ..... $ 4.00 AVAILABLE NOW 9x7 three bladed prop with a 1" diameter hub drilled for the GWS geardrives. Very flexible blades are tough to damage.

Gearboxes for Slowflyers, SPEED 280 & 300 motors

Gearboxes for Slowflyers,
SPEED 280 & 300 motors